17-09-2021

Hwh Troubleshooting Manual

HWH REGENERATIVE HYDRAULIC CIRCUIT ML37939/MP65.990M 20APR06 CYLINDER EXTEND The rod diameter is.875' or.601 sq. 3.14(.4375×.4375) The net force this cylinder will produce when the cylinder is extending is 0.601 (Area of the Rod) x P (3000 psi) = 1803 lbs. Page 10 Use the manual valve release for retracting the jacks only removed to gain access. Open valve 1-1/2 to 2 full turns. If the STORE feature on the HWH control panel will not DO NOT turn the 1/4' valve release nut more than retract the jacks. No matter if you lost your original Rheem water heater manual or the previous homeowners did not leave it behind, below you’ll find links to download user manuals in pdf format for the most popular and currently in-use Rheem residential water heaters. Make sure to visit our Rheem error codes page for help with troubleshooting tankless models. HWH systems are easy to operate and constructed of high quality components. All the HWH hydraulic leveling systems installed by Stuart's Service utilize the technology of the HWH Leveleze™ Light System. With indicator lights and arrows, Leveleze™ guides the user to a level motorhome quickly and effortlessly.

Service Manuals Leveling Systems Only. 200/310/610 Pilot Air Dump ML24343.PDF - Pilot Air Dump repair for 200/310/610 Leveling Systems for Winnebago motorized vehicles. 200/210/225 Series (Joystick) ML23934.PDF - HWH Joystick-Controlled Leveling System Featuring: Joystick BI-AXIS Control - Kick-Down or Straight-Acting Jacks - With/Without Air Dump. 310 Series (Manual Touch Panel).

Generate 128 bit hexadecimal key. From time to time the leveling solenoids on the front and rear hwh six packs develop leaks. The leaking of the o-rings is easy to find with the soap bubble test, and replacing them an easy project. Leaks inside the valves, at the seats, or internal o-ring, can be more difficult to diagnose and often exhibit themselves as leveling issues.


The six packs are easy to locate, they have airlines on one side and solenoid valves on the other. On each six pack there will be 6 solenoids. (2) are the R/L travel solenoids that work with the ride height control valve when you have a green travel light. (2) are the dump solenoids and (2) two are the raise solenoids. The dump and raise solenoids work when the system is in level mode.

O-ring Replacement

The valves are screwed on to the manifold with two o-rings, an inner o-ring and an outer o-ring. Those O-rings on the face of the valve make the seal against the “6-pack” manifold. The official HWH part number for the replacements is RAP6554.

Hwh Service Manuals

The OEM kit contains (1) #015 and (1) #028 o-ring, both with a standard round cross section. You should be able to go to any hardware store and find the same ones (Buna-N / Nitrile)

Hwh 325 series troubleshooting manual

Note that you can also easily remove the coil from each valve stem, its just held on by the nut on the end, remove that and it will lifts off. Sometimes that gives you a bit more room to maneuver. Don’t take off more than one at a time unless you mark where each one goes so you return them to the right stems.

The manifold should not be pitted / scratched where the o-rings seat. You should also clean off any debris on / around the seating surface, taking care not to knock any into the exposed openings.

A little grease on the o-rings is recommended by HWH, petroleum jelly or silicon grease are both good for this. Capcost program. If you use other than Buna-N / Nitrile materials (the most common) then you should check for material compatabilty. The lubrication is necessary to prevent tearing the o-rings as you lightly snug the valve down.

How tight to install, not sure if its 1/4 or 1/2 turn past finger tight, but you will get a feel for that when you remove the first one. Its a similar feel for an oil filter, with the same don’t over tighten warning.

New Valves

The HWH part number for our valves is RAP1940 for the raise and travel parts (3/32 orifice). The dump valves are a different number (RAP????) as they have a larger 5/32 orifice so they can move more air.

The valves contain a cone shaped seat, a plunger with a compliant face insert that rests on the seat, and a spring keeps it closed when the solenoid coil is not energized.

Replacing the HWH Plunger

Sometimes the seal at the seat will fail, maybe due to grit on the seat or often due to the compliant surface taking on a deep set with age. Although the valves are serviceable, you can take it apart to repair, finding a replacement piston/seat has been a problem. HWH will not sell just the piston, although they will service valves for less than 1/2 the cost of a full replacement.

Its been reported by some that you can reface the plunger face on a lathe, providing a new clean surface to the compliant face.

Others have used a Skinner replacement plunger V5-207-N (~$18) to replace the old plunger, however that has a smaller compliant seat of ~.20 vs the >.30 diameter on the original.

Use that information at your own risk, I am not endorsing use of the replacements.

The measurements of the piston are:

Hwh
  • Main Diameter: .442
  • Length: 1.175
  • Diameter at seat: .542
  • Diameter of seat: .290

Hwh 725 Leveling System Troubleshooting

O-Rings and Lubricants

Hwh 325 Series Troubleshooting Manual

There are O-ring materials that are not compatible with Vaseline petroleum jelly (same is true for silicone grease on some silicon O-rings). From the O-ring design and materials guide:

Hydrocarbon-based materials, such as petrolatum. As a clear to yellowish semisolid, petrolatum is better known as petroleum jelly (Vaseline®), but it is also available in liquid form. Petrolatum is typically suitable for use with

  1. Nitrile / Buna N (the most commonly used elastomer for O-rings and other sealing devices.)
  2. Chloroprene (often referred to by the trade name Neoprene)
  3. Polyurethane (Adiprene, Estane, Millathane, Morthane, Pellethane, Texin, Vibrathane)
  4. Silicone (general usage)
  5. Fluorosilicone (fluorovinylmethyl silicone rubber)
  6. Fluorocarbon (Viton)

You can also use the following site to check for chemical compatibility

For nearly two decades now, Stuart's Service has been installing and servicing HWH Hydraulic Leveling Systems on RVs, semi-trailers, ATVs and EMT vehicles. Consistent, high quality service has propelled Stuart's to the top – recognized by HWH as a five-star Master Service Center.

For the RV dealer, this means speedy, expert service at just the right price. For the RV owner, this means an end to uncomfortable nights & challenging dinners.

Hwh Hydraulic Leveling Troubleshooting

Here at Stuart's Service, we've leveled everything from RVs to ATV vehicles to semi-trailers to emergency vehicles. With an unlevel world out there, the need for efficient leveling is endless!

Hwh 625 Leveling System Troubleshooting

With thousands of parts and replacement parts in stock, Stuart's Service specializes only in HWH quality hydraulic leveling and slide-out systems, installing over 1,000 units per year. HWH systems are easy to operate and constructed of high quality components.

All the HWH hydraulic leveling systems installed by Stuart's Service utilize the technology of the HWH Leveleze™ Light System. With indicator lights and arrows, Leveleze™ guides the user to a level motorhome quickly and effortlessly. The convenient Leveleze™ interior panel allows the user to know at a glance, if any of the jacks are engaged before attempting to move the motorhome. This simple, yet vital feature can help prevent the costly damage caused by accidental moving.

Hwh Air Leveling System Manual

If you'd like to talk directly with someone about your leveling system needs, or if you need HWH replacement parts click on 'contact us', or e-mail Stuart's Service at cstuart@rvleveling.com.